CipherLab 1562 Guide de l'utilisateur Page 35
- Page / 82
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
27
Chapter 2
Selecting Output Interface
2.2.4 STOP BIT
By default, it is set 1 stop bit. Select 2 stop bits if necessary.
2.2.5 FLOW CONTROL
By default, there is no flow control in use. Select the flow control (handshake) method.
Options
Description
No No flow control
Scanner Ready
T
he scanner will activate the RTS signal upon powering on. After each good
read, the scanner will then wait for the CTS signal to become active. Data
will not be sent until the CTS signal becomes active.
Data Ready
T
he RTS signal will be activated after each good read. The scanner will then
wait for the CTS signal to become active. Data will not be sent until the CTS
signal becomes active.
Inverted Data Ready It works the same as the Data Ready flow control, except that the RTS
signal level is inverted.
2.2.6 INTER-CHARACTER DELAY
By default, the inter-character delay is set to zero. Enter a value, ranging from 0 to 254
in units of millisecond, to match the computer response time of the keyboard interface.
Such delay time is inserted between every character being transmitted. The longer the
delay time is, the slower the transmission speed will be.
2.2.7 INTER-FUNCTION DELAY
By default, the inter-function delay is set to zero. Enter a value, ranging from 0 to 254 in
units of millisecond, to match the computer response time of the keyboard interface.
Such delay time is inserted between every function code (0x01 ~ 0x1F) being transmitted.
The longer the delay time is, the slower the transmission speed will be.
2.2.8 ACK/NAK TIMEOUT
By default, the scanner sends data to the host without waiting for an ACK/NAK response
before sending more data. Enter a value, ranging from 1 to 99 in units of 0.1 second. If
no response within the specified period of time, the scanner will attempt to send the
same data three more times. If all the attempts fail without any notification, data loss will
occur.
Note: We suggest you to enable the error beep so that you will be notified of such data
loss and have the scanner re-read data.
- RELEASE NOTES 3
- CONTENTS 5
- INTRODUCTION 9
- USING SCANMASTER 10
- Introduction 11
- SETUP BARCODES 12
- SCANNER INFORMATION 14
- ScanMaster User Guide 18
- Chapter 1 19
- IN THIS CHAPTER 20
- 1.1 SCANNING MODE 20
- Changing Scanner Settings 21
- Chapter 1 21
- 1.7 AUTO SENSE (1500/1560) 25
- Chapter 2 27
- 2.1 KEYBOARD WEDGE 28
- 2.1.1 KEYBOARD TYPE 28
- 2.1.2 ALTERNATE COMPOSING 29
- 2.1.3 ALPHABETS TRANSMISSION 29
- 2.1.4 DIGITS TRANSMISSION 30
- 2.1.5 CAPITAL LOCK TYPE 30
- 2.1.6 CAPITAL LOCK STATE 30
- 2.1.7 ALPHABETS LAYOUT 31
- 2.1.8 DIGITS LAYOUT 32
- 2.1.9 LAPTOP SUPPORT 32
- 2.1.10 INTER-CHARACTER DELAY 33
- 2.1.11 INTER-FUNCTION DELAY 33
- 2.2 RS-232 34
- 2.2.1 BAUD RATE 34
- 2.2.2 DATA BITS 34
- 2.2.3 PARITY 34
- Chapter 2 35
- Selecting Output Interface 35
- 2.3 WAND EMULATION 36
- 2.3.1 MARGIN TIME 36
- 2.3.2 MODULE TIME 36
- 2.3.3 NORMAL STATE 37
- 2.3.4 BAR STATE 37
- 2.4 BLUETOOTH HID 38
- 2.4.1 KEYBOARD TYPE 38
- 2.4.5 BROADCASTING 40
- 2.4.6 SNIFF MODE 41
- 2.5 BLUETOOTH SPP 42
- 2.5.1 AUTHENTICATION 42
- 2.5.4 INTER-FUNCTIONAL DELAY 44
- 2.5.5 ACK/NAK TIMEOUT 44
- 2.6 USB HID 2.6 USB HID 45
- 2.7 USB VIRTUAL COM 46
- Chapter 3 47
- 3.1 CODABAR 49
- 3.2 CODE 25 — INDUSTRIAL 25 50
- 3.3 CODE 25 — INTERLEAVED 25 51
- 3.4 CODE 25 — MATRIX 25 51
- Chapter 3 53
- Changing Symbology Settings 53
- 3.12 MSI 56
- 3.13 FRENCH PHARMACODE 57
- 3.14 ITALIAN PHARMACODE 57
- 3.15 PLESSEY 58
- 3.17 TELEPEN 60
- Chapter 4 63
- 4.1 LETTER CASE 64
- 4.2 CHARACTER SUBSTITUTION 65
- 4.2.1 APPLICABLE CODE TYPES 65
- 4.3 PREFIX/SUFFIX CODE 66
- Prefix Code: None 66
- Chapter 4 67
- Defining Output Format 67
- 4.4 CODE ID 69
- 4.4.1 CODE ID SET 1~5 69
- 4.5 CODE LENGTH 71
- Code Type 72
- 4.7 REMOVE SPECIAL CHARACTER 73
- Chapter 5 75
- 5.1 FORMAT SELECTION 76
- 5.1.1 ENABLE EDITING FORMATS 76
- 5.1.2 EXCLUSIVE DATA EDITING 76
- Chapter 5 77
- Applying Editing Formats 77
- 5.2.2 FIELD SETTINGS 78
- 5.2.3 TRANSMISSION SEQUENCE 80
- 5.2.4 EXAMPLES 81
Produits connexes et manuels pour Lecteurs de codes-barres CipherLab 1562
(180 pages)
(277 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.028 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels