CipherLab 1266 Spécifications télécharger pdf (Page 103)

Update

Chapter 4

Changing Symbology Settings

4.6 CODE 93

You can only configure the scanner to read this symbology or not.

*Enable

Disable

4.7 CODE 128

You can only configure the scanner to read this symbology or not.

*Enable

Disable

1 2 ... 98 99 100 101 102 103 104 105 106 107 108 ... 179 180

1166 / 1266 Barcode Scanne 1
IMPORTANT NOTICES 3
RELEASE NOTES 5
CONTENTS 7
INTRODUCTION 13
SETTING UP 3666 15
DIRECT CHARGING 16
Introduction 17
SYMBOLOGIES SUPPORTED 18
QUICK START 21
ENTER CONFIGURATION MODE 23
EXIT CONFIGURATION MODE 23
DEFAULT SETTINGS 24
RESTORE SYSTEM DEFAULTS 24
Quick Start 25
 Refer to Appendix III 28
LIST THE CURRENT SETTINGS 29
Chapter 1 31
1.2 MEMORY 33
1.2.1 TRANSMIT BUFFER 33
1.2.2 MEMORY MODE 34
Chapter 1 35
1.4.1 GOOD READ BEEP 38
1.4.2 FREQUENCY 38
1.5 SCAN MODES 39
1.6 SCANNING TIMEOUT 43
 Laser mode 43
 Auto Off mode 43
 Auto Power Off mode 43
1.9 NEGATIVE BARCODES 46
Chapter 2 47
2.1 BT HID 48
2.1.2 RESET CONNECTION 49
Chapter 2 51
Selecting Output Interface 51
2.2 BT SPP SLAVE 58
2.3 KEYBOARD WEDGE VIA 3666 59
Keyboard Wedge via 3666 60
No. Keyboard Type No 60
Keyboard Type 60
2.3.2 KEYBOARD SETTINGS 61
US Keyboard Style – Normal 62
62
Cap Lock Type Description 64
Alphabets Transmission 66
ALT Composing 68
Laptop Support 68
2.3.3 INTER-CHARACTER DELAY 69
2.4 RS-232 VIA 3666 70
2.4.2 BAUD RATE 70
2.4.3 DATA BITS 71
2.4.4 PARITY 71
2.4.5 FLOW CONTROL 72
2.4.6 INTER-CHARACTER DELAY 72
Chapter 3 73
Set Connection 74
3.1.2 CHANGE INTERFACE 75
Sniff Mode (Power-saving) 76
3.2 CONNECTING VIA BLUETOOTH 77
3.2.1 CHANGE INTERFACE 77
Chapter 3 79
3.2.3 CONNECT TO DONGLE 81
Chapter 4 89
4.1 CODABAR 90
4.1.3 CLSI CONVERSION 91
4.2 CODE 25 – INDUSTRIAL 25 92
4.2.2 VERIFY CHECK DIGIT 93
4.2.3 TRANSMIT CHECK DIGIT 93
4.3 CODE 25 – INTERLEAVED 25 95
4.3.2 VERIFY CHECK DIGIT 96
4.3.3 TRANSMIT CHECK DIGIT 96
4.4 CODE 25 – MATRIX 25 98
4.4.2 VERIFY CHECK DIGIT 99
4.4.3 TRANSMIT CHECK DIGIT 99
4.5 CODE 39 101
4.5.2 VERIFY CHECK DIGIT 102
4.5.3 TRANSMIT CHECK DIGIT 102
4.6 CODE 93 103
4.7 CODE 128 103
4.8 EAN-8 104
4.8.1 CONVERT TO EAN-13 105
4.8.2 TRANSMIT CHECK DIGIT 105
4.9 EAN-13 106
4.9.1 ISBN CONVERSION 107
4.9.2 CONVERT TO ISSN 107
4.9.3 TRANSMIT CHECK DIGIT 107
4.10 GS1-128 (EAN-128) 108
4.10.1 TRANSMIT CODE ID 108
4.11 MSI 109
4.11.1 VERIFY CHECK DIGIT 109
4.11.2 TRANSMIT CHECK DIGIT 109
4.12 FRENCH PHARMACODE 111
4.12.1 TRANSMIT CHECK DIGIT 111
4.13 ITALIAN PHARMACODE 112
4.13.1 TRANSMIT CHECK DIGIT 112
4.14 PLESSEY 113
4.14.1 CONVERT TO UK PLESSEY 113
4.14.2 TRANSMIT CHECK DIGIT 113
Chapter 4 115
Changing Symbology Settings 115
Transmit Check Digit 116
 GS1 DataBar Expanded 117
Transmit Code ID 118
Transmit Application ID 118
4.16 TELEPEN 119
4.17 UPC-A 120
4.17.1 CONVERT TO EAN-13 121
4.17.3 TRANSMIT CHECK DIGIT 121
4.18 UPC-E 122
4.18.4 TRANSMIT CHECK DIGIT 124
Chapter 5 125
Chapter 5 127
Defining Output Format 127
5.3.2 CHANGE CODE ID 130
5.3.3 CLEAR CODE ID SETTINGS 131
5.4 LENGTH CODE 132
Chapter 6 137
6.1.2 EXCLUSIVE DATA EDITING 139
End Programming Format 140
6.2.2 RESTORE DEFAULT FORMAT 142
6.3.1 APPLICABLE CODE TYPE 143
6.3.2 DATA LENGTH 147
137 149
6.4.2 FIELD SETTINGS 150
143 155
Additional Fields 155
Key Type Key Status 155
145 157
6.6 PROGRAMMING EXAMPLES 158
6.6.1 EXAMPLE I 158
147 159
SPECIFICATIONS 161
Appendix I 163
 Click [OK] 164
USING BLUETOOTH 165
DONGLE 165
HOW TO UPGRADE 3666 FIRMWARE 167
Appendix I Firmware Upgrade 169
Enter Setup 170
SN: SW3000014 170
Appendix II 171
EXAMPLE 172
Appendix III 173
KEY TYPE & STATUS 174
KEY TYPE 174
KEY STATUS 174
Appendix IV 177
HEXADECIMAL SYSTEM 178
ASCII TABLE 179
USE PRESET PIN 180
DISABLE AUTHENTICATION 180

Commentaires sur ces manuels

Pas de commentaire

CipherLab 1266 Spécifications Page 103

Commentaires sur ces manuels

Produits connexes et manuels pour Lecteurs de codes-barres CipherLab 1266