CipherLab 1704 Spécifications Page 55
- Page / 226
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
43
Update
Chapter 1
Understanding the Barcode Scanner
1.14.3 IMAGE CROPPING
This is used to crop a captured image.
Disable Image Cropping: Present the full 1280 x 1024 pixels.
Enable Image Cropping: Crop the image to the pixel addresses specified.
Enable
*Disable
Note: The scanner has a cropping resolution of 4 pixels. Setting the cropping area to less
than 3 pixels transfers the entire image.
Crop to Pixel Address
For image cropping, set the pixel addresses from (0,0) to (1279, 1023) to crop to. Columns are
numbered from 0 to 1279, rows from 0 to 1023. Specify four values for Top, Left, Bottom, and
Right, where Top and Bottom correspond to row pixel addresses, and Left and Right correspond to
column pixel addresses. For example, for a 4 row x 8 column image in the extreme bottom-right
section of the image, set the following values:
Top = 1020, Bottom = 1023, Left = 1272, Right = 1279
Top (0~1023)
Left (0~1279)
Bottom (0~1023)
Right (0~1279)
1. Read the barcode above one at a time to specify its value.
2. Read the “
Decimal Value” barcode on page 211. For example, read “4”, “7” and “6” for a value
of 476.
3. Read the “Validate” barcode on the same page to complete this setting
- 1704 Barcode Scanne 1
- IMPORTANT NOTICES 3
- RELEASE NOTES 5
- CONTENTS 7
- INTRODUCTION 13
- SYMBOLOGIES SUPPORTED 15
- QUICK START 17
- ENTER CONFIGURATION MODE 18
- EXIT CONFIGURATION MODE 18
- Quick Start 19
- Refer to Appendix III 23
- LIST THE CURRENT SETTINGS 24
- Chapter 1 27
- 1.2.2 GOOD READ LED DURATION 29
- 1.3.2 GOOD READ BEEP 31
- 1.4 VIBRATOR 32
- 1.4.1 GOOD READ VIBRATOR 32
- 1.5 SEND “NR” TO HOST 33
- 1.6 SCAN MODES 34
- Chapter 1 35
- 1.6.6 ALTERNATE MODE 37
- 1.6.7 AIMING MODE 37
- 1.6.8 MULTI-BARCODE MODE 38
- 1.8 DELAY BETWEEN RE-READ 40
- Continuous mode 40
- Auto Power Off mode 40
- Alternate mode 40
- 1.9 READ REDUNDANCY (1D) 41
- 1.13 OPERATION MODE 44
- 1.13.2 ENTER/EXIT IMAGE MODE 47
- 1.13.3 IMAGE MODE SETTINGS 48
- 1.13.4 ENTER/EXIT VIDEO MODE 52
- 1.13.5 VIDEO MODE SETTINGS 52
- 1.14 IMAGER PREFERENCES 53
- 1.14.1 IMAGE ENHANCEMENT 53
- 1.14.2 IMAGE RESOLUTION 54
- 1.14.3 IMAGE CROPPING 55
- 1.14.4 IMAGE FILE FORMAT 56
- 1.14.5 BITS PER PIXEL 56
- 1.14.6 JPEG IMAGE OPTIONS 57
- 1.15 SIGNATURE CAPTURE 58
- 1.16 CABLE AUTO-DETECT 61
- Chapter 2 63
- IN THIS CHAPTER 64
- 2.1 KEYBOARD WEDGE 65
- Chapter 2 67
- Selecting Output Interface 67
- 2.1.3 INTER-CHARACTER DELAY 75
- 2.1.4 INTER-FUNCTION DELAY 75
- 2.2 RS-232 76
- 2.2.2 BAUD RATE 76
- 2.2.3 DATA BITS 77
- 2.2.4 PARITY 77
- 2.2.5 STOP BIT 77
- 2.2.6 FLOW CONTROL 78
- 2.2.7 INTER-CHARACTER DELAY 79
- 2.2.8 INTER-FUNCTION DELAY 79
- 2.2.9 ACK/NAK TIMEOUT 80
- 2.3 DIRECT USB HID 81
- 2.3.3 INTER-FUNCTION DELAY 89
- 2.4 DIRECT USB VIRTUAL COM 90
- 2.4.2 INTER-FUNCTION DELAY 90
- 2.4.3 ACK/NAK TIMEOUT 91
- Chapter 3 93
- 3.1 CODABAR 94
- 3.1.2 CLSI CONVERSION 94
- 3.2 CODE 25 – INDUSTRIAL 25 96
- 3.3 CODE 25 – INTERLEAVED 25 98
- 3.3.1 VERIFY CHECK DIGIT 98
- 3.3.2 TRANSMIT CHECK DIGIT 98
- 3.3.3 CONVERT TO EAN-13 99
- 1704 Barcode Scanner 100
- User Guide 100
- 3.4 CODE 25 – MATRIX 25 101
- 3.4.1 VERIFY CHECK DIGIT 101
- 3.4.2 TRANSMIT CHECK DIGIT 101
- 3.5 CODE 25 – CHINESE 25 103
- 3.7.2 TRANSMIT CHECK DIGIT 105
- 3.7 CODE 39 105
- 3.7.1 VERIFY CHECK DIGIT 105
- Chapter 3 107
- Changing Symbology Settings 107
- 3.8 TRIOPTIC CODE 39 108
- 3.9 CODE 93 109
- 3.10 CODE 128 111
- 3.11 GS1-128 (EAN-128) 112
- 3.11.1 TRANSMIT CODE ID 112
- GS1 DataBar Expanded 117
- 3.13.5 CONVERT TO UPC/EAN 119
- 3.14 MSI 120
- 3.14.1 VERIFY CHECK DIGIT 120
- 3.14.2 TRANSMIT CHECK DIGIT 120
- 3.15 EAN-8 122
- 3.16 EAN-13 123
- 3.16.1 CONVERT TO ISBN 124
- 3.16.2 CONVERT TO ISSN 124
- 3.18 UPC-A 126
- 3.18.2 TRANSMIT CHECK DIGIT 127
- 3.19 UPC-E 128
- 3.19.4 TRANSMIT CHECK DIGIT 130
- 3.20 CODE 11 131
- 3.20.1 VERIFY CHECK DIGIT 131
- 3.20.2 TRANSMIT CHECK DIGIT 131
- 3.21 COMPOSITE CODE 133
- 3.21.1 COMPOSITE CC-A/B 133
- 3.21.2 COMPOSITE CC-C 133
- 3.21.3 COMPOSITE TLC-39 133
- 3.22 US POSTAL CODE 135
- 3.22.1 US POSTNET 135
- 3.22.2 US PLANET 135
- 3.22.3 TRANSMIT CHECK DIGIT 135
- 3.23 UK POSTAL CODE 136
- 3.23.1 UK POSTAL 136
- 3.23.2 TRANSMIT CHECK DIGIT 136
- 3.24.5 UPU FICS POSTAL 138
- 3.25 2D SYMBOLOGIES 139
- 3.25.1 PDF417 139
- 3.25.2 MicroPDF417 139
- 3.25.3 DATA MATRIX 140
- 3.25.4 MAXICODE 141
- 3.25.5 QR CODE 141
- 3.25.6 MicroQR 141
- 3.25.7 AZTEC 141
- Chapter 4 145
- Chapter 4 147
- Defining Output Format 147
- 4.4.2 CHANGE CODE ID 162
- 4.4.3 CLEAR CODE ID SETTINGS 165
- 4.5 LENGTH CODE 166
- 4.6 MULTI-BARCODE EDITOR 174
- Code Type 174
- Chapter 5 179
- 5.1.2 EXCLUSIVE DATA EDITING 181
- 5.2.2 RESTORE DEFAULT FORMAT 184
- 5.3.1 APPLICABLE CODE TYPE 185
- 5.3.2 DATA LENGTH 195
- Specify a value 195
- 5.4.3 TOTAL NUMBER OF FIELDS 198
- 5.4.4 FIELD SETTINGS 199
- 189 201
- Field 3 Setting 201
- 191 203
- Field 5 Setting 203
- 5.4.5 PAUSE FIELD SETTING 205
- 195 207
- 5.6 PROGRAMMING EXAMPLES 208
- 5.6.1 EXAMPLE I 208
- 197 209
- SPECIFICATIONS 211
- Appendix I 213
- Click [OK] 214
- Appendix I Firmware Up 215
- Appendix II 217
- Appendix III 219
- KEY TYPE & STATUS 220
- KEY TYPE 220
- KEY STATUS 220
- EXAMPLE 221
- Appendix IV 223
- HEXADECIMAL SYSTEM 224
- ASCII TABLE 225
Produits connexes et manuels pour Lecteurs de codes-barres CipherLab 1704
(6 pages)
(277 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.023 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels