CipherLab 1704 Spécifications Page 78
- Page / 226
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
66
Enter Setup
1704 Barcode Scanner
User Guide
2.2.6 FLOW CONTROL
By default, there is no flow control in use. Select the flow control (handshake) method.
Options
Description
No No flow control
Scanner Ready The scanner will activate the RTS signal upon powering on. After each good
read, the scanner will then wait for the CTS signal to become active. Data
will not be sent until the CTS signal becomes active.
Data Ready The RTS signal will be activated after each good read. The scanner will
then wait for the CTS signal to become active. Data will not be sent until
the CTS signal becomes active.
Inverted Data Ready It works the same as the Data Ready flow control except that the RTS
signal level is inverted.
*None
Scanner Ready
Data Ready
Invert Data Ready
- 1704 Barcode Scanne 1
- IMPORTANT NOTICES 3
- RELEASE NOTES 5
- CONTENTS 7
- INTRODUCTION 13
- SYMBOLOGIES SUPPORTED 15
- QUICK START 17
- ENTER CONFIGURATION MODE 18
- EXIT CONFIGURATION MODE 18
- Quick Start 19
- Refer to Appendix III 23
- LIST THE CURRENT SETTINGS 24
- Chapter 1 27
- 1.2.2 GOOD READ LED DURATION 29
- 1.3.2 GOOD READ BEEP 31
- 1.4 VIBRATOR 32
- 1.4.1 GOOD READ VIBRATOR 32
- 1.5 SEND “NR” TO HOST 33
- 1.6 SCAN MODES 34
- Chapter 1 35
- 1.6.6 ALTERNATE MODE 37
- 1.6.7 AIMING MODE 37
- 1.6.8 MULTI-BARCODE MODE 38
- 1.8 DELAY BETWEEN RE-READ 40
- Continuous mode 40
- Auto Power Off mode 40
- Alternate mode 40
- 1.9 READ REDUNDANCY (1D) 41
- 1.13 OPERATION MODE 44
- 1.13.2 ENTER/EXIT IMAGE MODE 47
- 1.13.3 IMAGE MODE SETTINGS 48
- 1.13.4 ENTER/EXIT VIDEO MODE 52
- 1.13.5 VIDEO MODE SETTINGS 52
- 1.14 IMAGER PREFERENCES 53
- 1.14.1 IMAGE ENHANCEMENT 53
- 1.14.2 IMAGE RESOLUTION 54
- 1.14.3 IMAGE CROPPING 55
- 1.14.4 IMAGE FILE FORMAT 56
- 1.14.5 BITS PER PIXEL 56
- 1.14.6 JPEG IMAGE OPTIONS 57
- 1.15 SIGNATURE CAPTURE 58
- 1.16 CABLE AUTO-DETECT 61
- Chapter 2 63
- IN THIS CHAPTER 64
- 2.1 KEYBOARD WEDGE 65
- Chapter 2 67
- Selecting Output Interface 67
- 2.1.3 INTER-CHARACTER DELAY 75
- 2.1.4 INTER-FUNCTION DELAY 75
- 2.2 RS-232 76
- 2.2.2 BAUD RATE 76
- 2.2.3 DATA BITS 77
- 2.2.4 PARITY 77
- 2.2.5 STOP BIT 77
- 2.2.6 FLOW CONTROL 78
- 2.2.7 INTER-CHARACTER DELAY 79
- 2.2.8 INTER-FUNCTION DELAY 79
- 2.2.9 ACK/NAK TIMEOUT 80
- 2.3 DIRECT USB HID 81
- 2.3.3 INTER-FUNCTION DELAY 89
- 2.4 DIRECT USB VIRTUAL COM 90
- 2.4.2 INTER-FUNCTION DELAY 90
- 2.4.3 ACK/NAK TIMEOUT 91
- Chapter 3 93
- 3.1 CODABAR 94
- 3.1.2 CLSI CONVERSION 94
- 3.2 CODE 25 – INDUSTRIAL 25 96
- 3.3 CODE 25 – INTERLEAVED 25 98
- 3.3.1 VERIFY CHECK DIGIT 98
- 3.3.2 TRANSMIT CHECK DIGIT 98
- 3.3.3 CONVERT TO EAN-13 99
- 1704 Barcode Scanner 100
- User Guide 100
- 3.4 CODE 25 – MATRIX 25 101
- 3.4.1 VERIFY CHECK DIGIT 101
- 3.4.2 TRANSMIT CHECK DIGIT 101
- 3.5 CODE 25 – CHINESE 25 103
- 3.7.2 TRANSMIT CHECK DIGIT 105
- 3.7 CODE 39 105
- 3.7.1 VERIFY CHECK DIGIT 105
- Chapter 3 107
- Changing Symbology Settings 107
- 3.8 TRIOPTIC CODE 39 108
- 3.9 CODE 93 109
- 3.10 CODE 128 111
- 3.11 GS1-128 (EAN-128) 112
- 3.11.1 TRANSMIT CODE ID 112
- GS1 DataBar Expanded 117
- 3.13.5 CONVERT TO UPC/EAN 119
- 3.14 MSI 120
- 3.14.1 VERIFY CHECK DIGIT 120
- 3.14.2 TRANSMIT CHECK DIGIT 120
- 3.15 EAN-8 122
- 3.16 EAN-13 123
- 3.16.1 CONVERT TO ISBN 124
- 3.16.2 CONVERT TO ISSN 124
- 3.18 UPC-A 126
- 3.18.2 TRANSMIT CHECK DIGIT 127
- 3.19 UPC-E 128
- 3.19.4 TRANSMIT CHECK DIGIT 130
- 3.20 CODE 11 131
- 3.20.1 VERIFY CHECK DIGIT 131
- 3.20.2 TRANSMIT CHECK DIGIT 131
- 3.21 COMPOSITE CODE 133
- 3.21.1 COMPOSITE CC-A/B 133
- 3.21.2 COMPOSITE CC-C 133
- 3.21.3 COMPOSITE TLC-39 133
- 3.22 US POSTAL CODE 135
- 3.22.1 US POSTNET 135
- 3.22.2 US PLANET 135
- 3.22.3 TRANSMIT CHECK DIGIT 135
- 3.23 UK POSTAL CODE 136
- 3.23.1 UK POSTAL 136
- 3.23.2 TRANSMIT CHECK DIGIT 136
- 3.24.5 UPU FICS POSTAL 138
- 3.25 2D SYMBOLOGIES 139
- 3.25.1 PDF417 139
- 3.25.2 MicroPDF417 139
- 3.25.3 DATA MATRIX 140
- 3.25.4 MAXICODE 141
- 3.25.5 QR CODE 141
- 3.25.6 MicroQR 141
- 3.25.7 AZTEC 141
- Chapter 4 145
- Chapter 4 147
- Defining Output Format 147
- 4.4.2 CHANGE CODE ID 162
- 4.4.3 CLEAR CODE ID SETTINGS 165
- 4.5 LENGTH CODE 166
- 4.6 MULTI-BARCODE EDITOR 174
- Code Type 174
- Chapter 5 179
- 5.1.2 EXCLUSIVE DATA EDITING 181
- 5.2.2 RESTORE DEFAULT FORMAT 184
- 5.3.1 APPLICABLE CODE TYPE 185
- 5.3.2 DATA LENGTH 195
- Specify a value 195
- 5.4.3 TOTAL NUMBER OF FIELDS 198
- 5.4.4 FIELD SETTINGS 199
- 189 201
- Field 3 Setting 201
- 191 203
- Field 5 Setting 203
- 5.4.5 PAUSE FIELD SETTING 205
- 195 207
- 5.6 PROGRAMMING EXAMPLES 208
- 5.6.1 EXAMPLE I 208
- 197 209
- SPECIFICATIONS 211
- Appendix I 213
- Click [OK] 214
- Appendix I Firmware Up 215
- Appendix II 217
- Appendix III 219
- KEY TYPE & STATUS 220
- KEY TYPE 220
- KEY STATUS 220
- EXAMPLE 221
- Appendix IV 223
- HEXADECIMAL SYSTEM 224
- ASCII TABLE 225
Produits connexes et manuels pour Lecteurs de codes-barres CipherLab 1704
(6 pages)
(277 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.032 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels